6V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors

These Micro Metal Gearmotors have high-power, 6 V motors with a stall current of 1.5 A and a typical free-run current of 150 mA. They offer roughly the same performance as the 6V HP versions, but they feature long-life carbon brushes instead of precious metal brushes. 12 V versions are also available, offering approximately the same performance at 12 V as the 6V HPCB versions do at 6 V, just with half the current draw.

Micro Metal Gearmotor HPCB long-life carbon brushes (left) next to Micro Metal Gearmotor HP precious metal brushes (right).

The following table shows all of the versions available with the HPCB 6V motor:

HPCB 6V
(high-power, carbon brushes)
Rated
Voltage
Stall
Current
No-Load
Current
No-Load
Speed
(RPM)
Extrapolated
Stall Torque
Max
Power
(W)
Approx
Gear
Ratio


No Encoder

w/ Extended
Motor Shaft

w/ Encoder,
Back Conn.

w/ Encoder,
Side Conn.
(kg⋅cm) (oz⋅in)
6 V 1.5 A 170 mA 6500 0.09 1.3 5:1 #3060 #3082 #5178 #5179
150 mA 3300 0.17 2.4 1.3 10:1 #3061 #3071 #5180 #5181
2100 0.25 3.5 1.3 15:1 #4786 #4787 #5182 #5183
1100 0.45 6.2 1.2 30:1 #3062 #3072 #5184 #5185
650 0.74 10 1.2 50:1 #3063 #3073 #5186 #5187
430 1.1 15 1.3 75:1 #3064 #3074 #5188 #5189
330 1.6 22 1.3 100:1 #3065 #3075 #5190 #5191
220 2.0 28 1.1 150:1 #3066 #3076 #5192 #5193
160 2.8 39 1.1 210:1 #3067 #3077 #5194 #5195
130 3.2 44 1.1 250:1 #3068 #3078 #5196 #5197
110 3.4 47 1.0 298:1 #3069 #3079 #5198 #5199
85 5.0 69 1.1 380:1 #4796 #4797 #5200 #5201
33 11 150 1000:1 #3070 #3080 #5202 #5203

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg⋅cm (35 oz⋅in) for the 380:1 and 1000:1 gearboxes, and 2 kg⋅cm (25 oz⋅in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

Versions with other motors are also available. You can use the following selection boxes to choose from all of our Micro Metal Gearmotors versions:

Alternatives available with variations in these parameter(s): gear ratio motor type encoder Select variant…

Products in category “6V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors”

Pololu item #: 3060
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 4.995:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 6500 RPM, 170 mA 0.09 kg⋅cm (1 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3082
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 4.995:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 6500 RPM, 170 mA 0.09 kg⋅cm (1 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3061
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 9.96:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 3300 RPM, 150 mA 0.17 kg⋅cm (2.4 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3071
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 9.96:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 3300 RPM, 150 mA 0.17 kg⋅cm (2.4 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5180
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 9.96:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 3300 RPM, 150 mA 0.17 kg⋅cm (2.4 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5181
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 9.96:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 3300 RPM, 150 mA 0.17 kg⋅cm (2.4 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4786
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 15.25:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 2100 RPM, 150 mA 0.25 kg⋅cm (3.5 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4787
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 15.25:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 2100 RPM, 150 mA 0.25 kg⋅cm (3.5 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5182
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 15.25:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 2100 RPM, 150 mA 0.25 kg⋅cm (3.5 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5183
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 15.25:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 2100 RPM, 150 mA 0.25 kg⋅cm (3.5 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3062
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 29.86:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 1100 RPM, 150 mA 0.45 kg⋅cm (6.2 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3072
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 29.86:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 1100 RPM, 150 mA 0.45 kg⋅cm (6.2 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5184
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 29.86:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 1100 RPM, 150 mA 0.45 kg⋅cm (6.2 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5185
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 29.86:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 1100 RPM, 150 mA 0.45 kg⋅cm (6.2 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3063
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 51.45:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 650 RPM, 150 mA 0.74 kg⋅cm (10 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3073
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 51.45:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 650 RPM, 150 mA 0.74 kg⋅cm (10 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5186
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 51.45:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 650 RPM, 150 mA 0.74 kg⋅cm (10 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5187
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 51.45:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 650 RPM, 150 mA 0.74 kg⋅cm (10 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3064
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 75.81:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 430 RPM, 150 mA 1.1 kg⋅cm (15 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3074
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 75.81:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 430 RPM, 150 mA 1.1 kg⋅cm (15 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5188
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 75.81:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 430 RPM, 150 mA 1.1 kg⋅cm (15 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5189
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 75.81:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 430 RPM, 150 mA 1.1 kg⋅cm (15 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3065
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 100.37:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 330 RPM, 150 mA 1.6 kg⋅cm (22 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3075
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 100.37:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 330 RPM, 150 mA 1.6 kg⋅cm (22 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5190
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 100.37:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 330 RPM, 150 mA 1.6 kg⋅cm (22 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5191
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 100.37:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 330 RPM, 150 mA 1.6 kg⋅cm (22 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3066
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 150.58:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 220 RPM, 150 mA 2.0 kg⋅cm (27 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3076
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 150.58:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 220 RPM, 150 mA 2.0 kg⋅cm (27 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5192
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 150.58:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 220 RPM, 150 mA 2.0 kg⋅cm (27 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5193
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 150.58:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 220 RPM, 150 mA 2.0 kg⋅cm (27 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3067
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 210.59:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 160 RPM, 150 mA 2.8 kg⋅cm (38 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3077
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 210.59:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 160 RPM, 150 mA 2.8 kg⋅cm (38 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5194
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 210.59:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 160 RPM, 150 mA 2.8 kg⋅cm (38 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5195
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 210.59:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 160 RPM, 150 mA 2.8 kg⋅cm (38 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3068
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 248.98:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 130 RPM, 150 mA 3.2 kg⋅cm (44 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3078
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 248.98:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 130 RPM, 150 mA 3.2 kg⋅cm (44 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5196
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 248.98:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 130 RPM, 150 mA 3.2 kg⋅cm (44 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5197
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 248.98:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 130 RPM, 150 mA 3.2 kg⋅cm (44 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3069
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 297.92:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 110 RPM, 150 mA 3.4 kg⋅cm (47 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3079
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 297.92:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 110 RPM, 150 mA 3.4 kg⋅cm (47 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5198
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 297.92:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 110 RPM, 150 mA 3.4 kg⋅cm (47 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5199
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 297.92:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 110 RPM, 150 mA 3.4 kg⋅cm (47 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4796
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 379.17:1 with high-durability steel plates no encoder

voltage no-load performance stall extrapolation*
6 V 85 RPM, 150 mA 5.0 kg⋅cm (69 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4797
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 379.17:1 with high-durability steel plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 85 RPM, 150 mA 5.0 kg⋅cm (69 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5200
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 85 RPM, 150 mA 5.0 kg⋅cm (69 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5201
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 85 RPM, 150 mA 5.0 kg⋅cm (69 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3070
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 986.41:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 33 RPM, 150 mA 11 kg⋅cm (152 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3080
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 986.41:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 33 RPM, 150 mA 11 kg⋅cm (152 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5202
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 986.41:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 33 RPM, 150 mA 11 kg⋅cm (152 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5203
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 986.41:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 33 RPM, 150 mA 11 kg⋅cm (152 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5178
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 4.995:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 6500 RPM, 170 mA 0.09 kg⋅cm (1 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5179
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HPCB 6V: high-power 6V with carbon brushes 4.995:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 6500 RPM, 170 mA 0.09 kg⋅cm (1 oz⋅in), 1.5 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Related Products

Magnetic Encoder Pair Kit with Top-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit with Side-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Pololu Micro Metal Gearmotor Bracket Extended Pair
Pololu Micro Metal Gearmotor Bracket Pair - Black
Pololu Micro Metal Gearmotor Bracket Pair - White
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, #2-56 Holes (2-Pack)
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, M3 Holes (2-Pack)
12mm Hex Wheel Adapter for 3mm Shaft (2-Pack)
Machine Screw: M1.6, 3mm Length, Phillips (6-pack)
26:1 Sub-Micro Plastic Planetary Gearmotor 6Dx16L mm
136:1 Sub-Micro Plastic Planetary Gearmotor 6Dx19L mm
Zumo 32U4 Robot Kit (No Motors)

Related Categories

Micro Metal Gearmotors
6V High-Power (HP) Micro Metal Gearmotors
6V Medium-Power (MP) Micro Metal Gearmotors
6V Low-Power (LP) Micro Metal Gearmotors
12V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors
Encoders for Micro Metal Gearmotors
Pololu Wheels and Tracks
Brushed DC Motor Controllers
Brushed DC Motor Drivers
Current Sensors
Pololu 5″ Robot Chassis RRC04A
Zumo Robots and Accessories
20D Metal Gearmotors
Pololu Metal Gearmotors
Pololu Plastic Gearmotors
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors