6V High-Power (HP) Micro Metal Gearmotors

These Micro Metal Gearmotors have high-power (HP), 6 V motors with a stall current of 1.6 A and a typical free-run current of 100 mA. They offer roughly the same performance as the 6V HPCB versions, but they have lower-friction, shorter-life precious metal brushes instead of carbon brushes.

Micro Metal Gearmotor HPCB long-life carbon brushes (left) next to Micro Metal Gearmotor HP precious metal brushes (right).

The following table shows all of the versions available with the HP 6V motor:

HP 6V
(high-power)
Rated
Voltage
Stall
Current
No-Load
Current
No-Load
Speed
(RPM)
Extrapolated
Stall Torque
Max
Power
(W)
Approx
Gear
Ratio


No Encoder

w/ Extended
Motor Shaft

w/ Encoder,
Back Conn.

w/ Encoder,
Side Conn.
(kg⋅cm) (oz⋅in)
6 V 1.6 A 120 mA 6100 0.11 1.5 5:1 #1000 #2210 #5152 #5153
100 mA 3100 0.22 3.0 1.6 10:1 #999 #2211 #5154 #5155
2000 0.30 4.2 1.5 15:1 #4784 #4785 #5156 #5157
1000 0.57 7.9 1.5 30:1 #1093 #2212 #5158 #5159
590 0.86 12 1.3 50:1 #998 #2213 #5160 #5161
410 1.3 18 1.4 75:1 #2361 #2215 #5162 #5163
310 1.7 24 1.3 100:1 #1101 #2214 #5164 #5165
210 2.4 33 1.2 150:1 #997 #2386 #5166 #5167
150 3.0 42 1.1 210:1 #996 #2216 #5168 #5169
120 3.4 47 1.1 250:1 #995 #2217 #5170 #5171
100 4.0 56 1.1 298:1 #994 #2218 #5172 #5173
84 5.5 76 1.1 380:1 #4794 #4795 #5174 #5175
31 12 170 1000:1 #1595 #2373 #5176 #5177

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg⋅cm (35 oz⋅in) for the 380:1 and 1000:1 gearboxes, and 2 kg⋅cm (25 oz⋅in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

Versions with other motors are also available. You can use the following selection boxes to choose from all of our Micro Metal Gearmotors versions:

Alternatives available with variations in these parameter(s): gear ratio motor type encoder Select variant…

Products in category “6V High-Power (HP) Micro Metal Gearmotors”

Pololu item #: 1000
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 4.995:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 6100 RPM, 120 mA 0.11 kg⋅cm (1.5 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2210
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 4.995:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 6100 RPM, 120 mA 0.11 kg⋅cm (1.5 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 999
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 9.96:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 3100 RPM, 100 mA 0.22 kg⋅cm (3.1 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2211
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 9.96:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 3100 RPM, 100 mA 0.22 kg⋅cm (3.1 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5154
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 9.96:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 3100 RPM, 100 mA 0.22 kg⋅cm (3.1 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5155
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 9.96:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 3100 RPM, 100 mA 0.22 kg⋅cm (3.1 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4784
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 15.25:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 2000 RPM, 100 mA 0.30 kg⋅cm (4.2 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4785
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 15.25:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 2000 RPM, 100 mA 0.30 kg⋅cm (4.2 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5156
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 15.25:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 2000 RPM, 100 mA 0.30 kg⋅cm (4.2 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5157
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 15.25:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 2000 RPM, 100 mA 0.30 kg⋅cm (4.2 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1093
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 29.86:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 1000 RPM, 100 mA 0.57 kg⋅cm (7.9 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2212
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 29.86:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 1000 RPM, 100 mA 0.57 kg⋅cm (7.9 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5158
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 29.86:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 1000 RPM, 100 mA 0.57 kg⋅cm (7.9 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5159
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 29.86:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 1000 RPM, 100 mA 0.57 kg⋅cm (7.9 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 998
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 51.45:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 590 RPM, 100 mA 0.86 kg⋅cm (11 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2213
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 51.45:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 590 RPM, 100 mA 0.86 kg⋅cm (11 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5160
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 51.45:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 590 RPM, 100 mA 0.86 kg⋅cm (11 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5161
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 51.45:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 590 RPM, 100 mA 0.86 kg⋅cm (11 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2361
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 75.81:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 410 RPM, 100 mA 1.3 kg⋅cm (18 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2215
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 75.81:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 410 RPM, 100 mA 1.3 kg⋅cm (18 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5162
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 75.81:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 410 RPM, 100 mA 1.3 kg⋅cm (18 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5163
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 75.81:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 410 RPM, 100 mA 1.3 kg⋅cm (18 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1101
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 100.37:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 310 RPM, 100 mA 1.7 kg⋅cm (23 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2214
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 100.37:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 310 RPM, 100 mA 1.7 kg⋅cm (23 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5164
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 100.37:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 310 RPM, 100 mA 1.7 kg⋅cm (23 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5165
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 100.37:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 310 RPM, 100 mA 1.7 kg⋅cm (23 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 997
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 150.58:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 210 RPM, 100 mA 2.4 kg⋅cm (33 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2386
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 150.58:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 210 RPM, 100 mA 2.4 kg⋅cm (33 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5166
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 150.58:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 210 RPM, 100 mA 2.4 kg⋅cm (33 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5167
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 150.58:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 210 RPM, 100 mA 2.4 kg⋅cm (33 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 996
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 210.59:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 150 RPM, 100 mA 3.0 kg⋅cm (41 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2216
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 210.59:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 150 RPM, 100 mA 3.0 kg⋅cm (41 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5168
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 210.59:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 150 RPM, 100 mA 3.0 kg⋅cm (41 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5169
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 210.59:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 150 RPM, 100 mA 3.0 kg⋅cm (41 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 995
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 248.98:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 120 RPM, 100 mA 3.4 kg⋅cm (47 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2217
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 248.98:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 120 RPM, 100 mA 3.4 kg⋅cm (47 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5170
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 248.98:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 120 RPM, 100 mA 3.4 kg⋅cm (47 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5171
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 248.98:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 120 RPM, 100 mA 3.4 kg⋅cm (47 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 994
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 297.92:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 100 RPM, 100 mA 4.0 kg⋅cm (55 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2218
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 297.92:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 100 RPM, 100 mA 4.0 kg⋅cm (55 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5172
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 297.92:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 100 RPM, 100 mA 4.0 kg⋅cm (55 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5173
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 297.92:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 100 RPM, 100 mA 4.0 kg⋅cm (55 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4794
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 379.17:1 with high-durability steel plates no encoder

voltage no-load performance stall extrapolation*
6 V 84 RPM, 100 mA 5.5 kg⋅cm (76 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4795
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 379.17:1 with high-durability steel plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 84 RPM, 100 mA 5.5 kg⋅cm (76 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5174
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 84 RPM, 100 mA 5.5 kg⋅cm (76 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5175
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 84 RPM, 100 mA 5.5 kg⋅cm (76 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1595
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 986.41:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 31 RPM, 100 mA 12 kg⋅cm (166 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2373
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 986.41:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 31 RPM, 100 mA 12 kg⋅cm (166 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5176
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 986.41:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 31 RPM, 100 mA 12 kg⋅cm (166 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5177
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 986.41:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 31 RPM, 100 mA 12 kg⋅cm (166 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5152
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 4.995:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 6100 RPM, 120 mA 0.11 kg⋅cm (1.5 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5153
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
HP 6V: high-power 6V with precious metal brushes 4.995:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 6100 RPM, 120 mA 0.11 kg⋅cm (1.5 oz⋅in), 1.6 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Related Products

Magnetic Encoder Pair Kit with Top-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit with Side-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Pololu Micro Metal Gearmotor Bracket Extended Pair
Pololu Micro Metal Gearmotor Bracket Pair - Black
Pololu Micro Metal Gearmotor Bracket Pair - White
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, #2-56 Holes (2-Pack)
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, M3 Holes (2-Pack)
12mm Hex Wheel Adapter for 3mm Shaft (2-Pack)
Machine Screw: M1.6, 3mm Length, Phillips (6-pack)
26:1 Sub-Micro Plastic Planetary Gearmotor 6Dx16L mm
136:1 Sub-Micro Plastic Planetary Gearmotor 6Dx19L mm
Zumo 32U4 Robot Kit (No Motors)

Related Categories

Micro Metal Gearmotors
6V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors
6V Medium-Power (MP) Micro Metal Gearmotors
6V Low-Power (LP) Micro Metal Gearmotors
12V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors
Encoders for Micro Metal Gearmotors
Pololu Wheels and Tracks
Brushed DC Motor Controllers
Brushed DC Motor Drivers
Current Sensors
Pololu 5″ Robot Chassis RRC04A
Zumo Robots and Accessories
20D Metal Gearmotors
Pololu Metal Gearmotors
Pololu Plastic Gearmotors
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors