6V Low-Power (LP) Micro Metal Gearmotors

These Micro Metal Gearmotors have low-power (LP), 6 V motors with a stall current of 360 mA and a typical free-run current of 40 mA. The following table shows all of the versions available with the LP 6V motor:

LP 6V
(low-power)
Rated
Voltage
Stall
Current
No-Load
Current
No-Load
Speed
(RPM)
Extrapolated
Stall Torque
Max
Power
(W)
Approx
Gear
Ratio


No Encoder

w/ Extended
Motor Shaft

w/ Encoder,
Back Conn.

w/ Encoder,
Side Conn.
(kg⋅cm) (oz⋅in)
6 V 0.36 A 50 mA 2500 0.05 0.7 5:1 #1100 #2200 #5100 #5101
40 mA 1300 0.10 1.4 10:1 #1099 #2201 #5102 #5103
860 0.17 2.4 0.37 15:1 #4780 #4781 #5104 #5105
450 0.29 4.0 0.31 30:1 #993 #2202 #5106 #5107
270 0.44 6.1 0.29 50:1 #1098 #2203 #5108 #5109
180 0.64 8.9 0.29 75:1 #2360 #2209 #5110 #5111
130 0.74 10 0.25 100:1 #992 #2204 #5112 #5113
90 1.1 15 0.25 150:1 #1097 #2205 #5114 #5115
65 1.6 22 0.25 210:1 #1096 #2206 #5116 #5117
54 1.7 24 0.23 250:1 #1095 #2207 #5118 #5119
45 2.0 28 0.22 298:1 #1094 #2208 #5120 #5121
36 2.9 40 0.27 380:1 #4790 #4791 #5122 #5123
13 5.5 76 1000:1 #1596 #3058 #5124 #5125

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg⋅cm (35 oz⋅in) for the 380:1 and 1000:1 gearboxes, and 2 kg⋅cm (25 oz⋅in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

Versions with other motors are also available. You can use the following selection boxes to choose from all of our Micro Metal Gearmotors versions:

Alternatives available with variations in these parameter(s): gear ratio motor type encoder Select variant…

Products in category “6V Low-Power (LP) Micro Metal Gearmotors”

Pololu item #: 1100
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 4.995:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 2500 RPM, 50 mA 0.05 kg⋅cm (0.7 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2200
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 4.995:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 2500 RPM, 50 mA 0.05 kg⋅cm (0.7 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1099
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 9.96:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 1300 RPM, 40 mA 0.10 kg⋅cm (1.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2201
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 9.96:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 1300 RPM, 40 mA 0.10 kg⋅cm (1.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5102
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 9.96:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 1300 RPM, 40 mA 0.10 kg⋅cm (1.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5103
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 9.96:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 1300 RPM, 40 mA 0.10 kg⋅cm (1.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4780
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 15.25:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 860 RPM, 40 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4781
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 15.25:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 860 RPM, 40 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5104
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 15.25:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 860 RPM, 40 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5105
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 15.25:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 860 RPM, 40 mA 0.17 kg⋅cm (2.4 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 993
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 29.86:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 450 RPM, 40 mA 0.29 kg⋅cm (4.0 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2202
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 29.86:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 450 RPM, 40 mA 0.29 kg⋅cm (4.0 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5106
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 29.86:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 450 RPM, 40 mA 0.29 kg⋅cm (4.0 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5107
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 29.86:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 450 RPM, 40 mA 0.29 kg⋅cm (4.0 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1098
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 51.45:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 270 RPM, 40 mA 0.44 kg⋅cm (6.1 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2203
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 51.45:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 270 RPM, 40 mA 0.44 kg⋅cm (6.1 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5108
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 51.45:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 270 RPM, 40 mA 0.44 kg⋅cm (6.1 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5109
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 51.45:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 270 RPM, 40 mA 0.44 kg⋅cm (6.1 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2360
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 75.81:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 180 RPM, 40 mA 0.64 kg⋅cm (8.9 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2209
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 75.81:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 180 RPM, 40 mA 0.64 kg⋅cm (8.9 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5110
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 75.81:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 180 RPM, 40 mA 0.64 kg⋅cm (8.9 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5111
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 75.81:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 180 RPM, 40 mA 0.64 kg⋅cm (8.9 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 992
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 100.37:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 130 RPM, 40 mA 0.74 kg⋅cm (10 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2204
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 100.37:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 130 RPM, 40 mA 0.74 kg⋅cm (10 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5112
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 100.37:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 130 RPM, 40 mA 0.74 kg⋅cm (10 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5113
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 100.37:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 130 RPM, 40 mA 0.74 kg⋅cm (10 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1097
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 150.58:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 90 RPM, 40 mA 1.1 kg⋅cm (15 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2205
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 150.58:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 90 RPM, 40 mA 1.1 kg⋅cm (15 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5114
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 150.58:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 90 RPM, 40 mA 1.1 kg⋅cm (15 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5115
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 150.58:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 90 RPM, 40 mA 1.1 kg⋅cm (15 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1096
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 210.59:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 65 RPM, 40 mA 1.6 kg⋅cm (22 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2206
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 210.59:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 65 RPM, 40 mA 1.6 kg⋅cm (22 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5116
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 210.59:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 65 RPM, 40 mA 1.6 kg⋅cm (22 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5117
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 210.59:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 65 RPM, 40 mA 1.6 kg⋅cm (22 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1095
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 248.98:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 54 RPM, 40 mA 1.7 kg⋅cm (23 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2207
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 248.98:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 54 RPM, 40 mA 1.7 kg⋅cm (23 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5118
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 248.98:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 54 RPM, 40 mA 1.7 kg⋅cm (23 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5119
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 248.98:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 54 RPM, 40 mA 1.7 kg⋅cm (23 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1094
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 297.92:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 45 RPM, 40 mA 2.0 kg⋅cm (27 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 2208
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 297.92:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 45 RPM, 40 mA 2.0 kg⋅cm (27 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5120
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 297.92:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 45 RPM, 40 mA 2.0 kg⋅cm (27 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5121
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 297.92:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 45 RPM, 40 mA 2.0 kg⋅cm (27 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4790
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 379.17:1 with high-durability steel plates no encoder

voltage no-load performance stall extrapolation*
6 V 36 RPM, 40 mA 2.9 kg⋅cm (40 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 4791
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 379.17:1 with high-durability steel plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 36 RPM, 40 mA 2.9 kg⋅cm (40 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5122
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 36 RPM, 40 mA 2.9 kg⋅cm (40 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5123
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 379.17:1 with high-durability steel plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 36 RPM, 40 mA 2.9 kg⋅cm (40 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 1596
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 986.41:1 with brass plates no encoder

voltage no-load performance stall extrapolation*
6 V 13 RPM, 40 mA 5.5 kg⋅cm (76 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 3058
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 986.41:1 with brass plates encoder-compatible (extended motor shaft)

voltage no-load performance stall extrapolation*
6 V 13 RPM, 40 mA 5.5 kg⋅cm (76 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5124
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 986.41:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 13 RPM, 40 mA 5.5 kg⋅cm (76 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5125
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 986.41:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 13 RPM, 40 mA 5.5 kg⋅cm (76 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5100
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 4.995:1 with brass plates 12 CPR incremental quadrature with back connector

voltage no-load performance stall extrapolation*
6 V 2500 RPM, 50 mA 0.05 kg⋅cm (0.7 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Pololu item #: 5101
Brand: Pololu supply outlook
Status: Active and Preferred 
RoHS 3 compliant
Out of stock.
Quantity:

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.

motor/brush type gearbox encoder
LP 6V: low-power 6V with precious metal brushes 4.995:1 with brass plates 12 CPR incremental quadrature with side connector

voltage no-load performance stall extrapolation*
6 V 2500 RPM, 50 mA 0.05 kg⋅cm (0.7 oz⋅in), 0.36 A
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox.

Related Products

Magnetic Encoder Pair Kit with Top-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit with Side-Entry Connector for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Magnetic Encoder Pair Kit for Micro Metal Gearmotors, 12 CPR, 2.7-18V
Pololu Micro Metal Gearmotor Bracket Extended Pair
Pololu Micro Metal Gearmotor Bracket Pair - Black
Pololu Micro Metal Gearmotor Bracket Pair - White
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, #2-56 Holes (2-Pack)
Pololu Universal Aluminum Mounting Hub for 3mm Shaft, M3 Holes (2-Pack)
12mm Hex Wheel Adapter for 3mm Shaft (2-Pack)
Machine Screw: M1.6, 3mm Length, Phillips (6-pack)
26:1 Sub-Micro Plastic Planetary Gearmotor 6Dx16L mm
136:1 Sub-Micro Plastic Planetary Gearmotor 6Dx19L mm

Related Categories

Micro Metal Gearmotors
6V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors
6V High-Power (HP) Micro Metal Gearmotors
6V Medium-Power (MP) Micro Metal Gearmotors
12V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors
Encoders for Micro Metal Gearmotors
Pololu Wheels and Tracks
Brushed DC Motor Controllers
Brushed DC Motor Drivers
Current Sensors
Pololu 5″ Robot Chassis RRC04A
20D Metal Gearmotors
Pololu Metal Gearmotors
Pololu Plastic Gearmotors
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors